![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
maggoolee2525 medical school grad
![](images/avatars/gallery/Cartoon_Network/Sylvester.gif)
Joined: 21 Dec 2015 Posts: 85
![](templates/Cobalt/images/spacer.gif) |
Posted: Tue Oct 17, 2017 11:59 pm Post subject: 9400 |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
After changing drum dev and blade ....my 9400 keeps producing "over embossed prints.'.......
that uses alot of toner!......is there anyway to tone this done a little ...tried sds dev.3-01....toner dose
and changed the sensor reading to 100 from 115 but still getting the same result.....is there something else i can do to rectify this ' problem'....... |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
Chuck One medical school freshman
Joined: 26 Mar 2013 Posts: 15 Location: USA ![](templates/Cobalt/images/spacer.gif) |
Posted: Thu Oct 19, 2017 4:49 pm Post subject: |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
Make sure it is not in poster mode |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
maggoolee2525 medical school grad
![](images/avatars/gallery/Cartoon_Network/Sylvester.gif)
Joined: 21 Dec 2015 Posts: 85
![](templates/Cobalt/images/spacer.gif) |
Posted: Sat Oct 21, 2017 1:47 am Post subject: embossed prints 9400 |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
1."poster mode" was in " off" and it still produced those embossed prints
Next tried change : sds devconse setting from 121 to 100
will run in for a week to see changes
A nyone with other alternative pls chk in
2.Anyone have used working NTC pls let me know for purchase |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |