![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
Bubbleguts medical school senior
![](images/avatars/14102351935835acc0ba36c.jpg)
Joined: 16 Apr 2014 Posts: 39
![](templates/Cobalt/images/spacer.gif) |
Posted: Wed Dec 07, 2016 10:18 am Post subject: Quality missing toner |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
Hello,
Not sure what the cause this is I have replaced charge corona cleaned transfer corona. Could this be a voltage issue?
![](http://i168.photobucket.com/albums/u168/JRS161176/_20161207_084236.jpg) |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
bigal doctor
![](images/avatars/gallery/Disney/Dad.gif)
Joined: 17 Apr 2007 Posts: 352 Location: TEXAS ![](templates/Cobalt/images/spacer.gif) |
Posted: Wed Dec 07, 2016 10:43 am Post subject: 7100 |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
Its the Developing unit.
Check seal 9, looks like it came off and rubbing the developer roller.
Had this happen before! |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
Bubbleguts medical school senior
![](images/avatars/14102351935835acc0ba36c.jpg)
Joined: 16 Apr 2014 Posts: 39
![](templates/Cobalt/images/spacer.gif) |
Posted: Wed Dec 07, 2016 11:29 am Post subject: |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
Seals look OK Dev itself looks good this only has 3k prints |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
dlee doctor
Joined: 07 Nov 2006 Posts: 1459 Location: E. Syracuse NY ![](templates/Cobalt/images/spacer.gif) |
Posted: Wed Dec 07, 2016 4:56 pm Post subject: |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
The only time I've ever seen anything similar to that was when I forgot to put the side cover on (while test printing) and light would get into the development area and would cause the washed out sides. Do you have the two side covers off? |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
Bubbleguts medical school senior
![](images/avatars/14102351935835acc0ba36c.jpg)
Joined: 16 Apr 2014 Posts: 39
![](templates/Cobalt/images/spacer.gif) |
Posted: Wed Dec 07, 2016 5:35 pm Post subject: |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
There both on |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
dlee doctor
Joined: 07 Nov 2006 Posts: 1459 Location: E. Syracuse NY ![](templates/Cobalt/images/spacer.gif) |
Posted: Wed Dec 07, 2016 5:52 pm Post subject: |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
Hmm...I'm not sure but check the LED. Make sure the copper tabs aren't bent. That the ones between each LED are touching. That the copper tab on the Charge assy is tight and touching (grounded) the LED. |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
CHILLIN doctor
Joined: 05 Oct 2006 Posts: 950
![](templates/Cobalt/images/spacer.gif) |
Posted: Wed Dec 07, 2016 6:29 pm Post subject: |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
and check the copper tab that goes from the main charge assy to the printhead isn't bent and makes contact with the printhead |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |