|
|
|
|
|
|
|
|
|
|
Desertdog resident
Joined: 06 Dec 2004 Posts: 162 Location: Hinges of Hell |
Posted: Fri Jun 09, 2006 1:32 pm Post subject: 1880 not loading paper |
|
|
Good day fellow techs. Got a call from a customer today. I have not ran the call yet, and since I have not ran across this one yet, I figured I'd check here. They report that their 1880 will not load paper. I had them turn off the mach and load paper. Had them leave the door open and bypass the switch. The mach immediately drives the paper in the reverse direction till the mach reads out of paper. Same with the sheet bypass. Any ideas. _________________ "Learn how to work, Kid" - BTLS |
|
|
|
|
|
|
|
|
|
|
jojobutthead medical school grad
Joined: 21 Mar 2005 Posts: 68 Location: Upstate NY |
Posted: Fri Jun 09, 2006 5:24 pm Post subject: |
|
|
You have paper from a jam on a sensor. It's reversing so I'd say the second one in. |
|
|
|
|
|
|
|
|
|
|
KIPDOCTOR Site Admin
Joined: 31 Dec 1969 Posts: 1408 Location: Boston Area |
Posted: Fri Jun 09, 2006 6:01 pm Post subject: |
|
|
Most likely the forward roller is worn and slipping as the paper drives. As the paper loads and backs up, it looks for a set number of clock pulses. If the paper skips across this roller, the clock pulses skip. This is a very common issue with this model. A little trick you can try is to pick up some brake fluid and clean the roller with that. This is an old used car salesmans trick. Put a quart of brake fluid in the crankcase of a leaking engine and the brake fluid swells the rubber. then no leaks, for a while anyway.
Make sure you clean the roller with alcohal after the brake fluid. Or, you could just replace the roller. This would be my reccomendation. _________________ What we have gained in technology, we have lost in humanity. |
|
|
|
|
|
|
|
|
|
|
KIP Dude resident
Joined: 14 Feb 2006 Posts: 164 Location: Outside USA |
Posted: Sat Jun 10, 2006 1:27 am Post subject: |
|
|
Add some electrical tape to the centre black roller. This will increase the diameter and increase pressure against the paper. Then when the paper rolls back it will stop. This is common especially with new rolls of paper that have a lot of weight behind them. When the brake stops the roller there isn't enough friction and the paper slides through. _________________ Everytime something is made idiot proof... the world creates a better idiot! |
|
|
|
|
|
|
|
|
|
|
Vic dreaming of medical school
Joined: 12 Feb 2009 Posts: 8 Location: Canada |
Posted: Sun Mar 08, 2009 2:41 pm Post subject: |
|
|
On a top of everything that is said above. I found one of the causes that can contribute to this problem is a loosen screws in a paper spindle. Which causes to sag a bit under weight of a new roll. I usually tighten them down with the thread locker. |
|
|
|
|
|
|
|
|
|
|
Chazbo doctor
Joined: 05 Jul 2005 Posts: 377
|
Posted: Sun Mar 08, 2009 8:56 pm Post subject: |
|
|
the electrical tape works........make two lengths 8" long. stick tape length(one at a time) to the bottom of the roller,lined up with outer edge, and turn roller counter-clock-wise. _________________ Ride To Live |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|