|
|
|
|
|
|
|
|
|
|
xerox_7 resident
Joined: 01 Jun 2006 Posts: 229 Location: Columbia, Mo |
Posted: Tue Oct 22, 2013 7:15 pm Post subject: 2050 calibration |
|
|
I recently bought a used 7000 and 2050 scanner. When making copies from the 2050 the 30, 24, and 18 inch rolls do not line up sise to side. Does someone have a manual so I can do a side to side registration adjustment, or might there be another problem.
Thank You
Alan
Triangle Blueprints |
|
|
|
|
|
|
|
|
|
|
TXReproShop doctor
Joined: 04 Apr 2005 Posts: 300
|
Posted: Wed Oct 23, 2013 10:41 am Post subject: |
|
|
Check setting for Architecture or Engineering. |
|
|
|
|
|
|
|
|
|
|
xerox_7 resident
Joined: 01 Jun 2006 Posts: 229 Location: Columbia, Mo |
Posted: Wed Oct 23, 2013 11:52 am Post subject: Side to Side registration |
|
|
The paper settings on the 7000 are correct. Set for Arch. Is there a calibration on the 2050 to sense original size or position relative to center?
Thank You
Alan |
|
|
|
|
|
|
|
|
|
|
CHILLIN doctor
Joined: 05 Oct 2006 Posts: 950
|
Posted: Wed Oct 23, 2013 12:21 pm Post subject: |
|
|
Assuming the printer is printing correctly and centered.
Try printing the test patten from the front of the machine on 36inch paper and make sure it's centered.
Back Up Data #50 is the adjustment for Horizontal Center Point for Scanning.
If you increase the setting the image on the page should move to the left giving more right side margin.
If you decrease the setting the opposite.
BUD# 46 (Plain Paper) is the vertical zoom adjustment. The bigger number increases the vert. zoom
BUD# 42 (Plain Paper) is the horizontal zoom adjustment. The bigger number increases the Horizontal zoom.
FYI. I would print out the back up list before I start in case you make a mistake. |
|
|
|
|
|
|
|
|
|
|
xerox_7 resident
Joined: 01 Jun 2006 Posts: 229 Location: Columbia, Mo |
Posted: Wed Oct 23, 2013 4:39 pm Post subject: 2050 calibration |
|
|
Chillin:
Is this adjustment you are recommending a "global" setting, or is it done separately for each roll? The 36" originals print centered on 36" paper. I have to offset 30" originals about 1.5" to the right on the feedboard to have them print centered on a 30" roll.
Thanks
Alan |
|
|
|
|
|
|
|
|
|
|
dlee doctor
Joined: 07 Nov 2006 Posts: 1459 Location: E. Syracuse NY |
Posted: Thu Oct 24, 2013 10:00 am Post subject: |
|
|
Like TXReproShop said, I think you should check the Architectural/Engineering setting on the scanner (not printer). If you are running all Arch size drawings, it should be set to Architecture.
I'm reiterating this because you did not mention if you checked this yet and looks like you checked it on the printer instead of the scanner. |
|
|
|
|
|
|
|
|
|
|
xerox_7 resident
Joined: 01 Jun 2006 Posts: 229 Location: Columbia, Mo |
Posted: Thu Oct 24, 2013 12:16 pm Post subject: 2050 calibration |
|
|
Thank You TX Repro, It was the printer format I checked. I just checked the scanner format and it is set to "A", not "B". I assume "A" is architecture.
Thank You
Alan |
|
|
|
|
|
|
|
|
|
|
TXReproShop doctor
Joined: 04 Apr 2005 Posts: 300
|
Posted: Thu Oct 24, 2013 12:29 pm Post subject: |
|
|
On the scanner go to - MENU then SETTING - then ORIGINAL FORMAT
you will then have the choice of Architectural or Engineering. Which ever format you choose will show on the screen of the scanner as AR or EN |
|
|
|
|
|
|
|
|
|
|
xerox_7 resident
Joined: 01 Jun 2006 Posts: 229 Location: Columbia, Mo |
Posted: Thu Oct 24, 2013 1:49 pm Post subject: 2050 calibration |
|
|
My machine goes, "MENU", "SETTINGS", "ORIGINAL FORMAT". Then my choices are "A Series", and "B Series". I assume that "A" Series is architectural, and that is what it is set for.
Alan |
|
|
|
|
|
|
|
|
|
|
bigal doctor
Joined: 17 Apr 2007 Posts: 352 Location: TEXAS |
Posted: Thu Oct 24, 2013 2:12 pm Post subject: 2050 |
|
|
That's the Metric settings! Set I believe in BUD settings the scanner to English! |
|
|
|
|
|
|
|
|
|
|
xerox_7 resident
Joined: 01 Jun 2006 Posts: 229 Location: Columbia, Mo |
Posted: Thu Oct 24, 2013 5:57 pm Post subject: 2050 calibration |
|
|
BigAl: How do I access the BackUpData settings?
Thank You
Alan |
|
|
|
|
|
|
|
|
|
|
TXReproShop doctor
Joined: 04 Apr 2005 Posts: 300
|
Posted: Fri Oct 25, 2013 10:59 am Post subject: |
|
|
Not Big Al, but go to service mode on scanner, .135 (hold "." and press 1 3 5) You will find it under MENU - SETTINGS. |
|
|
|
|
|
|
|
|
|
|
xerox_7 resident
Joined: 01 Jun 2006 Posts: 229 Location: Columbia, Mo |
Posted: Fri Oct 25, 2013 11:55 am Post subject: 2050 calibration. |
|
|
TX Repro:
I have acessed the BUD chrt by using your entry method. What BUD setting changes the paper format under settings from metric to english.
Thank You
alan |
|
|
|
|
|
|
|
|
|
|
TXReproShop doctor
Joined: 04 Apr 2005 Posts: 300
|
Posted: Fri Oct 25, 2013 1:01 pm Post subject: |
|
|
No. 1 Value 1 is English
No. 2 Value 0 is American English
No. 3 Value 1 is Inch |
|
|
|
|
|
|
|
|
|
|
xerox_7 resident
Joined: 01 Jun 2006 Posts: 229 Location: Columbia, Mo |
Posted: Fri Oct 25, 2013 2:18 pm Post subject: 2050 calibration |
|
|
Thank You, problem solved.
Alan
Triangle Blueprints |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|