 |
|
|
|
|
|
|
|
|
|
ssbmi
medical school freshman
Joined: 14 Jun 2011
Posts: 24
Location: pacific
|
 Posted: Mon Oct 22, 2012 3:07 pm Post subject: kip 6000 dirty copies please view pictures. NEED HELP!! |
  |
|
 [/img]
_________________
thank you. |
|
| |
|
|
|
|
|
|
|
|
cjwilt
doctor
Joined: 24 Jan 2007
Posts: 1041
|
| Posted: Mon Oct 22, 2012 3:42 pm Post subject: |
|
|
| Looks like the developer is the problem. Did you open it to see if toner is getting passed the cleaning blade? |
|
| |
|
|
|
|
|
|
|
|
bigal
doctor
Joined: 17 Apr 2007
Posts: 352
Location: TEXAS
|
| Posted: Mon Oct 22, 2012 4:10 pm Post subject: dirty 6000 |
|
|
More than likely broken regulation gear. Look on right side of developer unit to see if the gear onthe brass hub is split in two.
Common problem , replace gear. Kip has a update for this. |
|
| |
|
|
|
|
|
|
|
|
ssbmi
medical school freshman
Joined: 14 Jun 2011
Posts: 24
Location: pacific
|
| Posted: Mon Oct 22, 2012 4:16 pm Post subject: |
|
|
YES CHECKED CLEANING BLADE, GEARS, CONTACTS, DRUM CHARGE, TC CHARGE, DRUM AND PRESSURE SPRINGS. PROBLEM IS INTERMITTTENT. I CAN'T FIGURE OUT THIS PROBLEM!! DEVELOPER UNIT HAS JUST BEEN REFURBISHED!!
_________________
thank you. |
|
| |
|
|
|
|
|
|
|
|
cjwilt
doctor
Joined: 24 Jan 2007
Posts: 1041
|
| Posted: Mon Oct 22, 2012 4:19 pm Post subject: |
|
|
| Did you check the bearings on the regulation roller? I have seen them lock up and cause issues like this too. |
|
| |
|
|
|
|
|
|
|
|
ssbmi
medical school freshman
Joined: 14 Jun 2011
Posts: 24
Location: pacific
|
| Posted: Mon Oct 22, 2012 4:26 pm Post subject: |
|
|
YES CHECKED ALL BEARING'S ON DEVELOPER UNIT.
_________________
thank you. |
|
| |
|
|
|
|
|
|
|
|
cjwilt
doctor
Joined: 24 Jan 2007
Posts: 1041
|
| Posted: Mon Oct 22, 2012 4:29 pm Post subject: |
|
|
| Do you have another developer to try in it? |
|
| |
|
|
|
|
|
|
|
|
arlen
resident
Joined: 30 Nov 2009
Posts: 157
Location: Salt Lake City, Utah
|
| Posted: Mon Oct 22, 2012 4:34 pm Post subject: |
|
|
| Are you seeing a build up of toner on the developer roll in that area? |
|
| |
|
|
|
|
|
|
|
|
ssbmi
medical school freshman
Joined: 14 Jun 2011
Posts: 24
Location: pacific
|
| Posted: Mon Oct 22, 2012 4:42 pm Post subject: |
|
|
YES TONER BUILDS UP ON THE DEVELOPER ROLLER IT LOOKS ALOT THICKER IN THAT AREA. ALSO TRIED TO SWITCH DEVELOPER UNIT AND IT DID THE SAME THING.
_________________
thank you.
Last edited by ssbmi on Mon Oct 22, 2012 4:48 pm; edited 1 time in total |
|
| |
|
|
|
|
|
|
|
|
arlen
resident
Joined: 30 Nov 2009
Posts: 157
Location: Salt Lake City, Utah
|
| Posted: Mon Oct 22, 2012 4:46 pm Post subject: |
|
|
| Did you clean the developer roll in your rebuild, or did you install a new one? If you cleaned it, What method did you use to clean it? |
|
| |
|
|
|
|
|
|
|
|
cjwilt
doctor
Joined: 24 Jan 2007
Posts: 1041
|
| Posted: Mon Oct 22, 2012 4:47 pm Post subject: |
|
|
Then the problem is the developer... I have seen this happen with bad regulation roller bearings a lot in the past. I have also seen it happen when that side of the regulation roller is not pressurized all the way. On time the nuts that are embedded in the plastic plate that you tighten the screw into for the pressure, were stripped in the plastic. This would not allow the screw to tighten down all the way and keep pressure on the rollers causing this same issue.
Good Luck |
|
| |
|
|
|
|
|
|
|
|
ssbmi
medical school freshman
Joined: 14 Jun 2011
Posts: 24
Location: pacific
|
| Posted: Mon Oct 22, 2012 5:00 pm Post subject: |
|
|
NOT SURE ON THE METHOD I PAY$ FOR IT TO BE REFURBISHED.
_________________
thank you. |
|
| |
|
|
|
|
|
|
|
|
arlen
resident
Joined: 30 Nov 2009
Posts: 157
Location: Salt Lake City, Utah
|
| Posted: Mon Oct 22, 2012 5:13 pm Post subject: |
|
|
I have found when there is a build up of toner on the 6000 drum like that, I have to clean it off carefully. I don't think the 6000 does a good job of cleaning excess toner off it's drum.
I have been dealing with this myself and have recently found that it seems to be easy not to get that side pressurized properly, as CJ pointed out.
Good Luck |
|
| |
|
|
|
|
|
|
|
|
dlee
doctor
Joined: 07 Nov 2006
Posts: 1459
Location: E. Syracuse NY
|
| Posted: Mon Oct 22, 2012 5:49 pm Post subject: |
|
|
It definitely looks like a gear. I would use the developer rotation tool and turn the developer unit and check for any hairline split gears. They will open up as you put pressure on them.
But you did say that you swapped the dev. unit with another and it did the same thing to that dev. unit also? Correct? |
|
| |
|
|
|
|
|
|
|
|
CHILLIN
doctor
Joined: 05 Oct 2006
Posts: 950
|
| Posted: Mon Oct 22, 2012 5:57 pm Post subject: |
|
|
| Check the gear that drives the regulation roller. The one with the 2 Allen screws on it. They tend to crack and look good but don't turn correctly. |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
