![](templates/Cobalt/images/spacer.gif) |
Home of the Kip Doctor!
REGISTER: In order to register for our forums please send an E mail to [email protected] stating what user name and password you would like. This is now required due to all the spambots that have been registering.
![KeepItPrinting.com Forum Index](images/logo/Cobalt.gif) |
KeepItPrinting.com The "unofficial' and "unauthorized" KIP info site.
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
dlee doctor
Joined: 07 Nov 2006 Posts: 1459 Location: E. Syracuse NY ![](templates/Cobalt/images/spacer.gif) |
Posted: Fri Feb 26, 2016 5:36 pm Post subject: |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
OK guys, I've gone thru everything that we've talked about above. My 9000 is randomly leaving a few prints that are 1/4 taller than the rest, (usually after a jam or paper change), It'll run 5 to 7 sheets that are 1/4 longer than ther rest then it starts to print correctly again. Any new information?[/quote] |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
mark in vegas doctor
![](images/avatars/1880118085581b53fd3c04b.gif)
Joined: 20 Oct 2010 Posts: 1852 Location: Las Vegas, NV ![](templates/Cobalt/images/spacer.gif) |
Posted: Fri Feb 26, 2016 7:22 pm Post subject: |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
Pull the two sprockets with half moon keys and look at the key and the shaft it sits in. Likely worn out shaft or the key has a grove pounded in it. I have replaced more than a few keys, sprockets and chains to remove slop in the drive. The sprocket on the left has a set screw that always loosens up. And take a look at the lower drive gears. If the teeth are worn and pointy (tech term) replace the gears. The gear on the paper feed clutch (the expensive one) becomes loose or cracked. After removing the slop my registration problem went away. PM me if you need a better explanation. _________________ Regards,
Mark
RVN 68-69
It's so nice to be insane
No one asks you to explain |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
|
|
![](templates/Cobalt/images/spacer.gif) |