![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
techpat medical school senior
Joined: 15 Sep 2006 Posts: 35 Location: quebec ![](templates/Cobalt/images/spacer.gif) |
Posted: Fri Aug 28, 2009 1:47 pm Post subject: Roll #1 unloading |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
I have problem with kip 2001, the problem is paper roll 1 unloading intermittent, I replace ph1 (paper set sensor), both clutch, brake, I ajust brake and I check all screw is tight, I replace ph2a (paper end clock 1st), I clean all contact in the drawer and I replace the holder counter roller #6601300041. I clean all rubber roller. Do you have any idea ? Thanks for your help.
pat. |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
Zoey doctor
![](images/avatars/17306755764e528c527b8de.jpg)
Joined: 15 Jan 2007 Posts: 359 Location: Midwest ![](templates/Cobalt/images/spacer.gif) |
Posted: Fri Aug 28, 2009 2:42 pm Post subject: |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
I had this happen a couple of months ago. Is drawer 2 doing it as well? In my case, drawer 1 was backing out and drawer 2 was jamming. Turned out there was a piece of paper in the cutter. I cleaned the cutter and all was good. |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
phan6622 doctor
Joined: 09 Feb 2007 Posts: 750 Location: Midwest ![](templates/Cobalt/images/spacer.gif) |
Posted: Fri Aug 28, 2009 2:51 pm Post subject: |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
I assume you have swapped spindles? |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
techpat medical school senior
Joined: 15 Sep 2006 Posts: 35 Location: quebec ![](templates/Cobalt/images/spacer.gif) |
Posted: Fri Aug 28, 2009 3:01 pm Post subject: |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
Zoey wrote: |
I had this happen a couple of months ago. Is drawer 2 doing it as well? In my case, drawer 1 was backing out and drawer 2 was jamming. Turned out there was a piece of paper in the cutter. I cleaned the cutter and all was good. |
I have to return monday to the customer and check the cutter unit, thanks for your help. |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
Chazbo doctor
Joined: 05 Jul 2005 Posts: 377
![](templates/Cobalt/images/spacer.gif) |
Posted: Fri Aug 28, 2009 3:29 pm Post subject: |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
The roll of paper may be slipping on the spindle. If so, remove the roll gripper on the spindle assy. and flatten the tooth end on both sides with a hammer. this will, in effect, make the teeth longer so they grip better _________________ Ride To Live
Last edited by Chazbo on Wed Sep 30, 2009 9:15 am; edited 1 time in total |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
Charlie Brown doctor
![](images/avatars/34749680949e7c4b3e22c9.gif)
Joined: 09 Aug 2005 Posts: 434 Location: Nashville Tennessee ![](templates/Cobalt/images/spacer.gif) |
Posted: Sat Aug 29, 2009 12:45 pm Post subject: |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
they have a gripper mod kit and this kit works grate. _________________ Charlie
I'll keep my Guns, Freedom, & Money ...... YOU CAN KEEP THE "CHANGE!"
I love my grandkids and My Country
I just don't love what my Govt is doing to MY COUNTRY |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
techpat medical school senior
Joined: 15 Sep 2006 Posts: 35 Location: quebec ![](templates/Cobalt/images/spacer.gif) |
Posted: Thu Sep 03, 2009 9:12 am Post subject: |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
Finaly i change the drawer to solve the problem, i dont know for what reason probably a wire ?
Thanks for your help.
Pat. |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
Jerry medical school grad
Joined: 07 Aug 2008 Posts: 54 Location: Oregon ![](templates/Cobalt/images/spacer.gif) |
Posted: Sat Jul 23, 2011 10:17 pm Post subject: Mod Kit? |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
Charlie Brown wrote: |
they have a gripper mod kit and this kit works grate. |
Would you have the part # for this mod, or more info.
thanks very much
Jerry |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |