|
Home of the Kip Doctor!
REGISTER: In order to register for our forums please send an E mail to [email protected] stating what user name and password you would like. This is now required due to all the spambots that have been registering.
|
KeepItPrinting.com The "unofficial' and "unauthorized" KIP info site.
|
|
|
|
|
|
|
|
|
|
|
graphic medical school grad
Joined: 15 Jan 2008 Posts: 78 Location: Broken Arrow, Ok |
Posted: Wed Jan 16, 2008 6:07 pm Post subject: Kip 1900 |
|
|
Customer had a paper jam in feed area. When they cleared the jam, a sensor actuator fell out with the paper. We replaced it on the P4 sensor. This did away with the J1 code we were getting but machine started showing a J2 code which, according to documentation, was a problem with the P6 sensor just before the U-turn area. We replaced it. After reassembling machine, we powered it up, everything looked fine but the fuser motor never actuated. Niether did the fan. The heater stayed lit for a few minutes and then it went out and would not come back on. We thought it had possibly blown the thermistor, thermostat, or SSR. I checked the old thermostat and thermistor with an ohm meter and they both showed open. We replaced all of these but did no good. Talked to Michael on Monday and he suggested that we make sure all voltages are present. When we went back after Christmas we powered the machine up, heater came on for a couple of minutes. Again, fuser motor and fan did not start. Bulb went out and will not come back up. We tried a new power relay but did no good. Fuser motor will work in service mode but heat lamp will not. Checked lamp for resistance and ohm meter showed 0 ohms. Not sure if getting 24volts to bulb but we have checked so many voltages I can't really remember. The SSR is receiving 24 volts. When lamp did come on, after it went out it did not declare any fault codes. Any help you can offer would be greatly appreciated. |
|
|
|
|
|
|
|
|
|
|
phan6622 doctor
Joined: 09 Feb 2007 Posts: 750 Location: Midwest |
Posted: Thu Jan 17, 2008 12:15 am Post subject: |
|
|
I have had thermisters that checked out ok with a meter, but then failed under any kind of load..
Just a thought.. |
|
|
|
|
|
|
|
|
|
|
Yamadog medical school senior
Joined: 25 Jan 2008 Posts: 43
|
Posted: Sun Jan 27, 2008 11:21 pm Post subject: KIP 1900 |
|
|
Check the brightness of the lamp when it comes on. It may not be able to heat up enough before it times out! |
|
|
|
|
|
|
|
|
|
|
CHILLIN doctor
Joined: 05 Oct 2006 Posts: 950
|
Posted: Mon Jan 28, 2008 5:14 pm Post subject: |
|
|
On the right side of the machine behind the cover the is a line of connectors. 5-6 I think. Not sure how you replaced the sensors but if
un-hooked these connectors. The are two small white connectors each with two wires. If you reverse these two connectors the fuser wil not heat up. Generally they will blow the thermostat, but not always. Also if you unhooked the wires on the SSR make sure that you plugged them back in correctly. Good luck. |
|
|
|
|
|
|
|
|
|
|
graphic medical school grad
Joined: 15 Jan 2008 Posts: 78 Location: Broken Arrow, Ok |
Posted: Mon Feb 25, 2008 2:05 pm Post subject: KIP 1900 |
|
|
Hey all. Thanks for your suggestions. We did get the machine up and running however, it is making foggy copies. There is a toner halo around the letters and where a letter has an opening such as a capital A or B, etc., the openings are grey. Also there is a light gray background throughout.This machine was hit with a power surge when power was restored after our big ice storm a couple of months ago. Any suggestions on copy quality issue. Have checked the mag roller, erase lamps, exposure, doc. glass, developer bias, toner density. All changes that were made had no effect on copies. Did not lighten or darken. Also tried new drum. HELP. |
|
|
|
|
|
|
|
|
|
|
graphic medical school grad
Joined: 15 Jan 2008 Posts: 78 Location: Broken Arrow, Ok |
Posted: Thu Mar 13, 2008 9:37 am Post subject: |
|
|
This machine if finally up and running good. We appreciate all of your help. Take care and God bless. |
|
|
|
|
|
|
|
|
|
|
lombardomarc medical school freshman
Joined: 14 Feb 2008 Posts: 17
|
Posted: Thu Feb 12, 2009 10:15 am Post subject: |
|
|
What did u do to get rid of the halo around the letters? |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
|
|
|