|
Home of the Kip Doctor!
REGISTER: In order to register for our forums please send an E mail to [email protected] stating what user name and password you would like. This is now required due to all the spambots that have been registering.
|
KeepItPrinting.com The "unofficial' and "unauthorized" KIP info site.
|
|
|
|
|
|
|
|
|
|
|
dlee doctor
Joined: 07 Nov 2006 Posts: 1459 Location: E. Syracuse NY |
Posted: Tue Jun 18, 2019 3:24 pm Post subject: KIP7170K fuser creaking noise |
|
|
Last 2 KIP7170K installs, anytime the fuser is rotating, there is an intermittent creaking noise. When the fuser warms and during printing, you can hear the creaking happen at a consistent rate and when it slows to stop printing, the creaking slows as well. 2 in a row, I'm I the only one? |
|
|
|
|
|
|
|
|
|
|
mark in vegas doctor
Joined: 20 Oct 2010 Posts: 1852 Location: Las Vegas, NV |
Posted: Tue Jun 18, 2019 6:01 pm Post subject: |
|
|
Are you able to determine if it's the exit transports or something internal? I have been unable to control any sounds from the exit transports without unplugging the printer _________________ Regards,
Mark
RVN 68-69
It's so nice to be insane
No one asks you to explain |
|
|
|
|
|
|
|
|
|
|
CHILLIN doctor
Joined: 05 Oct 2006 Posts: 950
|
Posted: Tue Jun 18, 2019 9:32 pm Post subject: |
|
|
Check the silver covers on the end of the fuser rollers that the heater rods go through. I’m seeing these are not pushed in all the way on some of the machine right off the crate. I think they maybe getting jarred loose a little during shipping. |
|
|
|
|
|
|
|
|
|
|
slyman doctor
Joined: 23 Apr 2008 Posts: 467 Location: Sherbrooke,Quebec |
Posted: Tue Jun 25, 2019 5:25 pm Post subject: |
|
|
You can try to remove 1 or 2 turn of pressure on the pressure roller and add some high temp oil in the pressure roller bearings. Those are problematic for that kind of noise.
That problem appear since the 7100 |
|
|
|
|
|
|
|
|
|
|
dlee doctor
Joined: 07 Nov 2006 Posts: 1459 Location: E. Syracuse NY |
Posted: Wed Jun 26, 2019 11:05 am Post subject: |
|
|
First one, on the 3rd time of full disassembly, the creaking went away. Didn't do anything different except inspected all the bearings and shafts, etc. Adjusting the pressure did not do anything. 2nd one, 3 days later, KIP Tech and my other tech went there and they heard nothing. It might've worked itself out.
Just received our 3rd 7170K, so lets hope it's not 3 for 3. |
|
|
|
|
|
|
|
|
|
|
adcart8 medical school freshman
Joined: 16 Apr 2018 Posts: 11
|
Posted: Fri Oct 11, 2019 1:16 pm Post subject: Silver Inserts |
|
|
Yes, as previously mentioned by CHILLIN, the thin metal inserts for the Fuser often make a screeching noise. I have heard it a couple times and every time I have been able to trace it to this piece. If nothing else, you may need to just pull the Fuser out and inspect it, paying close attention to all those Washers and Tensioners on the sides. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
|
|
|