|
Home of the Kip Doctor!
REGISTER: In order to register for our forums please send an E mail to [email protected] stating what user name and password you would like. This is now required due to all the spambots that have been registering.
|
KeepItPrinting.com The "unofficial' and "unauthorized" KIP info site.
|
|
|
|
|
|
|
|
|
|
|
dlee doctor
Joined: 07 Nov 2006 Posts: 1459 Location: E. Syracuse NY |
Posted: Tue Nov 22, 2016 12:18 pm Post subject: Very random voids |
|
|
Hey guys. I have a 7170 with only 40K SF on it. For some reason, it has started doing random quarter size or 1" and 2" squiggly voids on prints. No steady void pattern, no repeat of lost image down the print. When I run the 36x60 print, the void randomly happens around 8", 12", 26", 38", 42" or 48" from LE. Some prints have only 1 or 2 while others may have 5 or 6. They are random and can be on left center or right side. Sometimes a couple side by side, 3" or 4" apart.
This customer runs 99% 24x36, so it isn't the "long print voids" with the fuser speed, even though I did adjust speeds to see if it would change anything and it did not.
I replaced the transfer corona and selected Transfer Support, no luck. I don't think it could be the drum. Not sure if it could be the paper as I tried different rolls, no difference.
Am I going to have to replace the drum/transfer seperation unit? |
|
|
|
|
|
|
|
|
|
|
mark in vegas doctor
Joined: 20 Oct 2010 Posts: 1852 Location: Las Vegas, NV |
Posted: Tue Nov 22, 2016 12:51 pm Post subject: |
|
|
Did you take a look at the fuser NIP? The spring loaded baffle in front of the TS? _________________ Regards,
Mark
RVN 68-69
It's so nice to be insane
No one asks you to explain |
|
|
|
|
|
|
|
|
|
|
dlee doctor
Joined: 07 Nov 2006 Posts: 1459 Location: E. Syracuse NY |
Posted: Tue Nov 22, 2016 1:54 pm Post subject: |
|
|
NIP is good. Baffle is as it should be. I believe the problem lays somewhere in the drum/ T/S assy area. We just unpacked a new 7170K, might just go swap t/s assy, to eliminate that possibility. |
|
|
|
|
|
|
|
|
|
|
mark in vegas doctor
Joined: 20 Oct 2010 Posts: 1852 Location: Las Vegas, NV |
Posted: Tue Nov 22, 2016 2:24 pm Post subject: |
|
|
Good idea _________________ Regards,
Mark
RVN 68-69
It's so nice to be insane
No one asks you to explain |
|
|
|
|
|
|
|
|
|
|
mark in vegas doctor
Joined: 20 Oct 2010 Posts: 1852 Location: Las Vegas, NV |
Posted: Tue Nov 22, 2016 8:58 pm Post subject: |
|
|
Take a roll of your paper over to the customer _________________ Regards,
Mark
RVN 68-69
It's so nice to be insane
No one asks you to explain |
|
|
|
|
|
|
|
|
|
|
caltech doctor
Joined: 24 Feb 2006 Posts: 262 Location: Northern California |
Posted: Fri Dec 02, 2016 7:58 pm Post subject: |
|
|
We had a 7100 doing this with a customer that runs very long prints 10 feet plus. The machine was not level. Lowered the feet and leveled the machine, prints good long prints now. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
|
|
|