|
|
|
|
|
|
|
|
|
|
copyman intern
Joined: 15 Aug 2007 Posts: 147 Location: new jersey / phila |
Posted: Tue Feb 09, 2016 2:57 pm Post subject: 3100 no paper found |
|
|
New customer called and said machine not recognizing the 2 rolls. LCD has something like no paper found for both paper rolls.
In the service window it says rolls are 11"
I seem to recall having this on a 3000 and it was because the machine wasn't closing right.
I had them push down on left side after then close drawer, turn machine off and on. Didn't help.
I don't work on a lot of wide formats, only the 3000 up to this point.
Any help appreciated.
Thanks in advance |
|
|
|
|
|
|
|
|
|
|
jezebel09 resident
Joined: 12 Jun 2013 Posts: 209
|
Posted: Tue Feb 09, 2016 3:04 pm Post subject: |
|
|
On the right hand side above the paper rolls is an LCD readout. Have them take the cover off this panel and read what is showing.
On the touchscreen, other than 11" rolls showing, is there any other indication showing? _________________ **************************************
Ockham's razor - usually is the best answer....
************************************** |
|
|
|
|
|
|
|
|
|
|
cezwhat resident
Joined: 24 Aug 2005 Posts: 221 Location: On the Prairie |
Posted: Tue Feb 09, 2016 3:28 pm Post subject: |
|
|
Open and close the fuser door. I have seen the fuser door intermittent connection or not close completely closed cause this condition. |
|
|
|
|
|
|
|
|
|
|
copyman intern
Joined: 15 Aug 2007 Posts: 147 Location: new jersey / phila |
Posted: Tue Feb 09, 2016 4:46 pm Post subject: |
|
|
Jez, in the LCD window is where it has 11" for both rolls |
|
|
|
|
|
|
|
|
|
|
dlee doctor
Joined: 07 Nov 2006 Posts: 1459 Location: E. Syracuse NY |
Posted: Tue Feb 09, 2016 5:25 pm Post subject: |
|
|
If it's a new customer with a 3000, I'm guessing it's a used 3000. I used to have the issue where you had the stacking device setting turned on for the 3000 and it would not show roll information. This 3000 might have had a stacker behind it at one time and it might be looking for it. You 'll have to go into service mode and see if it's turned on or off. Make sure it's off, if they don't have an attached stacker. |
|
|
|
|
|
|
|
|
|
|
jezebel09 resident
Joined: 12 Jun 2013 Posts: 209
|
Posted: Tue Feb 09, 2016 8:41 pm Post subject: |
|
|
If this is a new or reinstall, then the machine may show 11" until it is set via the touchscreen. What happens when you try to set it on the touchscreen?
Is there anything showing on the touchscreen? _________________ **************************************
Ockham's razor - usually is the best answer....
************************************** |
|
|
|
|
|
|
|
|
|
|
copyman intern
Joined: 15 Aug 2007 Posts: 147 Location: new jersey / phila |
Posted: Wed Feb 10, 2016 12:51 am Post subject: |
|
|
I will be looking at it on Thurs and will report back. All they reported is the touch screen has "no roll paper" or something like that, for both rolls.
In the lcd service screen is has Ready R1-11", R2-11"
By the way as I wrote in my first post it is a 3100 |
|
|
|
|
|
|
|
|
|
|
slyman doctor
Joined: 23 Apr 2008 Posts: 467 Location: Sherbrooke,Quebec |
Posted: Thu Feb 11, 2016 4:11 pm Post subject: |
|
|
Unattend is probably not working or you got a windows (on desktop) showing that there is no communication with the controller card.
First, check if you got all the information (soft version/firmware version...) in the Help screen
Second, close the GUI and take a look if Unattend is working and if yes, what it is showing.
If you got a bad communication screen, turn off machine, open IPS box and re-seat the controller card.
You may also a bad connection between the drawer and the frame of the machine, make sure the machine is on level and correct seated on floor.
And last thing, you may have to re-ghost, got to do it once with that problem. |
|
|
|
|
|
|
|
|
|
|
copyman intern
Joined: 15 Aug 2007 Posts: 147 Location: new jersey / phila |
Posted: Thu Feb 11, 2016 4:40 pm Post subject: Update |
|
|
Hey Slyman think you may have hit the nail on the head. Didn't see your message until I was back at my office.
Tried everything mentioned on some of the posts here and few other things, didn't solve problem. Ended up calling my friend at Kip and first thing he asked was if the meters were on the screen, they were not. He had me go into IPS diagnostics and delete all the jobs in C & D drives. Rebooted with the option checked to repair. After re-boot it recognized the paper rolls and worked good. Meters are only thing that didn't come back.
Thanks again |
|
|
|
|
|
|
|
|
|
|
slyman doctor
Joined: 23 Apr 2008 Posts: 467 Location: Sherbrooke,Quebec |
Posted: Thu Feb 11, 2016 5:43 pm Post subject: |
|
|
What do you mean by "reboot with option checked to repair"?
Also, what version do you have now ? |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|