|
|
|
|
|
|
|
|
|
|
mark in vegas doctor
Joined: 20 Oct 2010 Posts: 1852 Location: Las Vegas, NV |
Posted: Wed Jan 25, 2012 2:56 pm Post subject: |
|
|
My guess is they would decline to make an offer. By default that would make it a fine target. Actually I haven't been in the store, turned into a real tourist trap. _________________ Regards,
Mark
RVN 68-69
It's so nice to be insane
No one asks you to explain |
|
|
|
|
|
|
|
|
|
|
Chazbo doctor
Joined: 05 Jul 2005 Posts: 377
|
Posted: Wed Jan 25, 2012 3:17 pm Post subject: |
|
|
ok...plan "B"
tape the paper clip real good
paint a bulls eye target on it
you know the rest of the story _________________ Ride To Live |
|
|
|
|
|
|
|
|
|
|
mark in vegas doctor
Joined: 20 Oct 2010 Posts: 1852 Location: Las Vegas, NV |
Posted: Wed Jan 25, 2012 3:32 pm Post subject: |
|
|
Oh yeah! _________________ Regards,
Mark
RVN 68-69
It's so nice to be insane
No one asks you to explain |
|
|
|
|
|
|
|
|
|
|
dlee doctor
Joined: 07 Nov 2006 Posts: 1459 Location: E. Syracuse NY |
Posted: Wed Jan 25, 2012 4:48 pm Post subject: |
|
|
Well I put the old motor back in and stuck the paperclip back in place. I stuck it in the motor side of the plug where the wires go into from the motor to plug. As good as old now but working. Now I have to find out how much the motor drive board is OR just leave alone since it is printing.
I'd rather send myself to Vegas then this machine.....and it'll probably cost the same. |
|
|
|
|
|
|
|
|
|
|
mark in vegas doctor
Joined: 20 Oct 2010 Posts: 1852 Location: Las Vegas, NV |
Posted: Wed Jan 25, 2012 5:28 pm Post subject: |
|
|
The cost would be less until you stepped off the plane _________________ Regards,
Mark
RVN 68-69
It's so nice to be insane
No one asks you to explain |
|
|
|
|
|
|
|
|
|
|
Chazbo doctor
Joined: 05 Jul 2005 Posts: 377
|
Posted: Wed Jan 25, 2012 6:16 pm Post subject: |
|
|
leave it be.......I take the pads off of most of my units...no harm done _________________ Ride To Live |
|
|
|
|
|
|
|
|
|
|
dlee doctor
Joined: 07 Nov 2006 Posts: 1459 Location: E. Syracuse NY |
Posted: Wed Jan 25, 2012 6:26 pm Post subject: |
|
|
Yeah...I was planning on leaving it be since it is working. There is no harm done since it is just the cleaning motor and I did leave the pads off. I sent an email to KIP to see if the board was still available but I think I'll just let it be for now.
Like I said before, they put in a request for a new machine and am awaiting approval so it might not be long before it is getting replaced. |
|
|
|
|
|
|
|
|
|
|
mark in vegas doctor
Joined: 20 Oct 2010 Posts: 1852 Location: Las Vegas, NV |
Posted: Wed Jan 25, 2012 8:34 pm Post subject: |
|
|
It occurs to me that if the motor is installed with the label towards the contact it might produce the same result. I don't believe the label is conductive. Or maybe it just doesn't matter... _________________ Regards,
Mark
RVN 68-69
It's so nice to be insane
No one asks you to explain |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|