![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
awtech medical school grad
Joined: 06 May 2008 Posts: 99
![](templates/Cobalt/images/spacer.gif) |
Posted: Wed Jul 20, 2011 4:45 pm Post subject: Controller will not power on when Kip turns on |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
The embedded controller in one of our Kip 6000's will not power on when the Kip is powered on every time. Sometimes it will and sometimes it will not. To get it to work I had to plug the controller directly into the wall. I unplugged the serial cable. I unpluged the controller cmos battery. Then I can get into the bios and set it to power on after power loss. If I leave the serial cable plugged in, when I shutdown the Kip I will have to take out the battery again to get it to boot. |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
TXReproShop doctor
Joined: 04 Apr 2005 Posts: 300
![](templates/Cobalt/images/spacer.gif) |
Posted: Wed Jul 20, 2011 6:09 pm Post subject: |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
If it comes down to it, I have a complete controller. It was in one of my in-house machines that I took out of service earlier this year, and was working fine. |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
wadetech intern
Joined: 05 Jan 2009 Posts: 127
![](templates/Cobalt/images/spacer.gif) |
Posted: Tue Jul 26, 2011 4:22 pm Post subject: |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
Try the UPS Card....sometimes its just the fuse blown on the board.
Good Luck
WT |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
wadetech intern
Joined: 05 Jan 2009 Posts: 127
![](templates/Cobalt/images/spacer.gif) |
Posted: Tue Jul 26, 2011 4:26 pm Post subject: |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
PC Control PCB
Part Number 6606260260 |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
KIPDOCTOR Site Admin
![](images/avatars/gallery/Cartoon_Network/Superman.gif)
Joined: 31 Dec 1969 Posts: 1408 Location: Boston Area ![](templates/Cobalt/images/spacer.gif) |
Posted: Sun Jul 31, 2011 10:44 am Post subject: |
![Back to top](templates/Cobalt/images/icon_top.gif) |
|
There is also a bank of jumper pins on the MB. One set of them is labeled PW SW ( power switch). Crossing these pins momentarily function as a power switch input. The controller will boot. You may have a dead CMOS battery. Common. But I think also your fuse on the UPS board in the 6000 is also bad as others have mentioned. _________________ What we have gained in technology, we have lost in humanity. |
|
|
|
|
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
|
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |
![](templates/Cobalt/images/spacer.gif) |