 |
|
|
|
|
|
|
|
|
|
joe
medical school grad
Joined: 06 May 2007
Posts: 65
Location: ohio
|
 Posted: Thu May 05, 2011 11:15 am Post subject: fuser error E-000 |
  |
|
I am getting a fuser error E-000 on the gui and small lcd screen. fuser lamp will not light up, replaced fuser lamp, relay 1 ssr1, th1&2,checked fuse (ok) and 24v on dc controller (orange line )ok manual states that j220-4 is where 24 should be but the only orange wires(2) on the dc controller is cn-2 where i got my 24v.question would bad thermostat in fuser cause this issue? and does anyone have any ideas on how to resolve this?
thanks for any advice.
joe |
|
| |
|
|
|
|
|
|
|
|
megamind
dreaming of medical school
Joined: 16 Apr 2011
Posts: 9
Location: middle east
|
| Posted: Sat May 07, 2011 2:08 pm Post subject: E-0000 |
|
|
| I have encountered 2 kip 3100 with E-0000 , have tried what you have done and ended of replacing thermostat and started working. In addition check the relay 1 & 2. |
|
| |
|
|
|
|
|
|
|
|
slyman
doctor
Joined: 23 Apr 2008
Posts: 467
Location: Sherbrooke,Quebec
|
| Posted: Sun May 08, 2011 9:57 pm Post subject: |
|
|
you're not wrote it but I'm sure you have reset the error code in the service mode ? just in case...
I had to replace the thermistor too on the first 3000's I had. |
|
| |
|
|
|
|
|
|
|
|
joe
medical school grad
Joined: 06 May 2007
Posts: 65
Location: ohio
|
| Posted: Mon May 09, 2011 8:37 am Post subject: E-000 |
|
|
It ended up being a bad thermostat.
thanks for the responses guys.
joe |
|
| |
|
|
|
|
|
|
|
|
slyman
doctor
Joined: 23 Apr 2008
Posts: 467
Location: Sherbrooke,Quebec
|
| Posted: Mon May 09, 2011 10:08 pm Post subject: |
|
|
| Good to know, never had to replace the thermostat. |
|
| |
|
|
|
|
|
|
|
|
Chinh_KIP
medical school freshman
Joined: 29 Nov 2010
Posts: 12
|
| Posted: Mon Jun 20, 2011 6:00 am Post subject: |
|
|
I have issue with Kip 3000 with error E-000, When I turn on printer , in the screen appear error E-000 , I want to enter Sub Menu to clear error but all segments on the LCD light and I cannot enter service mode . Does anyone know what the happen with this machine ?
Thanks |
|
| |
|
|
|
|
|
|
|
|
drews
medical school senior
Joined: 19 Nov 2009
Posts: 44
Location: Memphis-Home of the Blues!
|
| Posted: Mon Jun 27, 2011 2:19 pm Post subject: |
|
|
Also, old firmware can cause E-000 Fuser too cold to pop up. I've updated 3 machines with the new firmware and it has fixed them. I think it's version 10...I'd have to grab my laptop and check.
_________________
Drew S. |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
